/** * Copyright (c) 2020 Bosch Sensortec GmbH. All rights reserved. * * BSD-3-Clause * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * 3. Neither the name of the copyright holder nor the names of its * contributors may be used to endorse or promote products derived from * this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * * @file bma423.h * @date 2020-05-08 * @version V2.14.13 * */ /** * \ingroup bma4xy * \defgroup bma423 BMA423 * @brief Sensor driver for BMA423 sensor */ #ifndef BMA423_H #define BMA423_H #ifdef __cplusplus extern "C" { #endif #include "bma4.h" /**\name Chip ID of BMA423 sensor */ #define BMA423_CHIP_ID UINT8_C(0x11) #define BMA425_CHIP_ID UINT8_C(0x13) /**\ Configuration ID start position of BMA423 sensor */ #define BMA423_CONFIG_ID_START_ADDR UINT8_C(66) /**\name Sensor feature size */ #define BMA423_FEATURE_SIZE UINT8_C(70) #define BMA423_ANY_MOT_LEN UINT8_C(4) /**\name Feature offset address */ #define BMA423_ANY_MOT_OFFSET UINT8_C(0x00) #define BMA423_NO_MOT_OFFSET UINT8_C(0x04) #define BMA423_STEP_CNTR_PARAM_OFFSET UINT8_C(0x08) #define BMA423_STEP_CNTR_OFFSET UINT8_C(0x3A) #define BMA423_SINGLE_TAP_OFFSET UINT8_C(0x3C) #define BMA423_DOUBLE_TAP_OFFSET UINT8_C(0x3E) #define BMA423_WRIST_WEAR_OFFSET UINT8_C(0x40) #define BMA423_CONFIG_ID_OFFSET UINT8_C(0x42) #define BMA423_AXES_REMAP_OFFSET UINT8_C(0x44) /**\name Read/Write Lengths */ #define BMA423_RD_WR_MIN_LEN UINT8_C(2) #define BMA423_NO_MOT_RD_WR_LEN (BMA423_ANY_MOT_LEN + BMA423_NO_MOT_OFFSET) /*! @name Mask definitions for major and minor config */ #define BMA423_CONFIG_MAJOR_MSK UINT16_C(0X3C0) #define BMA423_CONFIG_MINOR_MSK UINT8_C(0X1F) /*! @name Bit position for major config */ #define BMA423_CONFIG_MAJOR_POS UINT8_C(0X06) /**************************************************************/ /**\name Re-map Axes */ /**************************************************************/ #define BMA423_X_AXIS_MASK UINT8_C(0x03) #define BMA423_X_AXIS_SIGN_MASK UINT8_C(0x04) #define BMA423_Y_AXIS_MASK UINT8_C(0x18) #define BMA423_Y_AXIS_SIGN_MASK UINT8_C(0x20) #define BMA423_Z_AXIS_MASK UINT8_C(0xC0) #define BMA423_Z_AXIS_SIGN_MASK UINT8_C(0x01) /**************************************************************/ /**\name Step Counter/Detector/Activity */ /**************************************************************/ /**\name Step counter/activity enable macros */ #define BMA423_STEP_CNTR_EN_MSK UINT8_C(0x10) #define BMA423_STEP_ACT_EN_MSK UINT8_C(0x20) /**\name Step counter water-mark macros */ #define BMA423_STEP_CNTR_WM_MSK UINT16_C(0x03FF) /**\name Step counter reset macros */ #define BMA423_STEP_CNTR_RST_POS UINT8_C(2) #define BMA423_STEP_CNTR_RST_MSK UINT8_C(0x04) /**\name Step detector enable macros */ #define BMA423_STEP_DETECTOR_EN_POS UINT8_C(3) #define BMA423_STEP_DETECTOR_EN_MSK UINT8_C(0x08) /**\name Wrist-wear enable macros */ #define BMA423_WRIST_WEAR_EN_MSK UINT8_C(0x01) /**\name Step count output length*/ #define BMA423_STEP_CNTR_DATA_SIZE UINT16_C(4) /**\name single tap enable macros */ #define BMA423_SINGLE_TAP_EN_MSK UINT8_C(0x01) /**\name double tap enable macros */ #define BMA423_DOUBLE_TAP_EN_MSK UINT8_C(0x01) /**\name tap sensitivity macros */ #define BMA423_TAP_SENS_POS UINT8_C(1) #define BMA423_TAP_SENS_MSK UINT8_C(0x0E) /**\name Tap selection macro */ #define BMA423_TAP_SEL_POS UINT8_C(4) #define BMA423_TAP_SEL_MSK UINT8_C(0x10) /**************************************************************/ /**\name Any/no Motion */ /**************************************************************/ /**\name Any/No motion threshold macros */ #define BMA423_ANY_NO_MOT_THRES_MSK UINT16_C(0x07FF) /**\name Any/No motion duration macros */ #define BMA423_ANY_NO_MOT_DUR_MSK UINT16_C(0x1FFF) /**\name Any/No motion enable macros */ #define BMA423_ANY_NO_MOT_AXIS_EN_POS UINT8_C(0x0D) #define BMA423_ANY_NO_MOT_AXIS_EN_MSK UINT16_C(0xE000) /**************************************************************/ /**\name User macros */ /**************************************************************/ /**\name Any-motion/No-motion axis enable macros */ #define BMA423_X_AXIS_EN UINT8_C(0x01) #define BMA423_Y_AXIS_EN UINT8_C(0x02) #define BMA423_Z_AXIS_EN UINT8_C(0x04) #define BMA423_EN_ALL_AXIS UINT8_C(0x07) #define BMA423_DIS_ALL_AXIS UINT8_C(0x00) /**\name Feature enable macros for the sensor */ #define BMA423_STEP_CNTR UINT8_C(0x01) #define BMA423_STEP_ACT UINT8_C(0x02) #define BMA423_WRIST_WEAR UINT8_C(0x04) #define BMA423_SINGLE_TAP UINT8_C(0x08) #define BMA423_DOUBLE_TAP UINT8_C(0x10) /**\name Interrupt status macros */ #define BMA423_SINGLE_TAP_INT UINT8_C(0x01) #define BMA423_STEP_CNTR_INT UINT8_C(0x02) #define BMA423_ACTIVITY_INT UINT8_C(0x04) #define BMA423_WRIST_WEAR_INT UINT8_C(0x08) #define BMA423_DOUBLE_TAP_INT UINT8_C(0x10) #define BMA423_ANY_MOT_INT UINT8_C(0x20) #define BMA423_NO_MOT_INT UINT8_C(0x40) #define BMA423_ERROR_INT UINT8_C(0x80) /**\name Activity recognition macros */ #define BMA423_USER_STATIONARY UINT8_C(0x00) #define BMA423_USER_WALKING UINT8_C(0x01) #define BMA423_USER_RUNNING UINT8_C(0x02) #define BMA423_STATE_INVALID UINT8_C(0x03) /******************************************************************************/ /*! @name Structure Declarations */ /******************************************************************************/ /*! * @brief Any/No motion configuration */ struct bma423_any_no_mot_config { /*! Expressed in 50 Hz samples (20 ms) */ uint16_t duration; /*! Threshold value for Any-motion/No-motion detection in * 5.11g format */ uint16_t threshold; /*! To enable selected axes */ uint8_t axes_en; }; /*! * @brief Axes re-mapping configuration */ struct bma423_axes_remap { /*! Re-mapped x-axis */ uint8_t x_axis; /*! Re-mapped y-axis */ uint8_t y_axis; /*! Re-mapped z-axis */ uint8_t z_axis; /*! Re-mapped x-axis sign */ uint8_t x_axis_sign; /*! Re-mapped y-axis sign */ uint8_t y_axis_sign; /*! Re-mapped z-axis sign */ uint8_t z_axis_sign; }; /*! * @brief Step counter param settings */ struct bma423_stepcounter_settings { /*! Step Counter param 1 */ uint16_t param1; /*! Step Counter param 2 */ uint16_t param2; /*! Step Counter param 3 */ uint16_t param3; /*! Step Counter param 4 */ uint16_t param4; /*! Step Counter param 5 */ uint16_t param5; /*! Step Counter param 6 */ uint16_t param6; /*! Step Counter param 7 */ uint16_t param7; /*! Step Counter param 8 */ uint16_t param8; /*! Step Counter param 9 */ uint16_t param9; /*! Step Counter param 10 */ uint16_t param10; /*! Step Counter param 11 */ uint16_t param11; /*! Step Counter param 12 */ uint16_t param12; /*! Step Counter param 13 */ uint16_t param13; /*! Step Counter param 14 */ uint16_t param14; /*! Step Counter param 15 */ uint16_t param15; /*! Step Counter param 16 */ uint16_t param16; /*! Step Counter param 17 */ uint16_t param17; /*! Step Counter param 18 */ uint16_t param18; /*! Step Counter param 19 */ uint16_t param19; /*! Step Counter param 20 */ uint16_t param20; /*! Step Counter param 21 */ uint16_t param21; /*! Step Counter param 22 */ uint16_t param22; /*! Step Counter param 23 */ uint16_t param23; /*! Step Counter param 24 */ uint16_t param24; /*! Step Counter param 25 */ uint16_t param25; }; /***************************************************************************/ /*! BMA423 User Interface function prototypes ****************************************************************************/ /** * \ingroup bma423 * \defgroup bma423ApiInit Initialization * @brief Initialize the sensor and device structure */ /*! * \ingroup bma423ApiInit * \page bma423_api_bma423_init bma423_init * \code * int8_t bma423_init(struct bma4_dev *dev); * \endcode * @details This API is the entry point. * Call this API before using all other APIs. * This API reads the chip-id of the sensor and sets the resolution. * * @param[in,out] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_init(struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiConfig ConfigFile * @brief Write binary configuration in the sensor */ /*! * \ingroup bma423ApiConfig * \page bma423_api_bma423_write_config_file bma423_write_config_file * \code * int8_t bma423_write_config_file(struct bma4_dev *dev); * \endcode * @details This API is used to upload the config file to enable the features of * the sensor. * * @param[in] dev : Structure instance of bma4_dev. * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_write_config_file(struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiConfigId ConfigId * @brief Get Configuration ID of the sensor */ /*! * \ingroup bma423ApiConfig * \page bma423_api_bma423_get_config_id bma423_get_config_id * \code * int8_t bma423_get_config_id(uint16_t *config_id, struct bma4_dev *dev); * \endcode * @details This API is used to get the configuration id of the sensor. * * @param[out] config_id : Pointer variable used to store the configuration id. * @param[in] dev : Structure instance of bma4_dev. * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_get_config_id(uint16_t *config_id, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiMapInt Map / Unmap Interrupt * @brief Map / Unmap user provided interrupt to interrupt pin1 or pin2 of the sensor */ /*! * \ingroup bma423ApiMapInt * \page bma423_api_bma423_map_interrupt bma423_map_interrupt * \code * int8_t bma423_map_interrupt(uint8_t int_line, uint16_t int_map, uint8_t enable, struct bma4_dev *dev); * \endcode * @details This API sets/unsets the user provided interrupt to either * interrupt pin1 or pin2 in the sensor. * * @param[in] int_line: Variable to select either interrupt pin1 or pin2. * *@verbatim * int_line | Macros * ------------|------------------- * 0x00 | BMA4_INTR1_MAP * 0x01 | BMA4_INTR2_MAP *@endverbatim * * @param[in] int_map : Variable to specify the interrupts. * @param[in] enable : Variable to specify mapping or unmapping of interrupts. * *@verbatim * enable | Macros * --------|------------------- * 0x00 | BMA4_DISABLE * 0x01 | BMA4_ENABLE *@endverbatim * * @param[in] dev : Structure instance of bma4_dev. * * @note Below macros specify the interrupts. * * Feature Interrupts * - BMA423_STEP_CNTR_INT * - BMA423_ACTIVITY_INT * - BMA423_WRIST_WEAR_INT * - BMA423_WAKEUP_INT * - BMA423_ANY_MOT_INT * - BMA423_NO_MOT_INT * - BMA423_ERROR_INT * * Hardware Interrupts * - BMA4_FIFO_FULL_INT * - BMA4_FIFO_WM_INT * - BMA4_DATA_RDY_INT * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_map_interrupt(uint8_t int_line, uint16_t int_map, uint8_t enable, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiIntS Interrupt Status * @brief Read interrupt status of the sensor */ /*! * \ingroup bma423ApiIntS * \page bma423_api_bma423_read_int_status bma423_read_int_status * \code * int8_t bma423_read_int_status(uint16_t *int_status, struct bma4_dev *dev); * \endcode * @details This API reads the bma423 interrupt status from the sensor. * * @param[out] int_status : Variable to store the interrupt status read from * the sensor. * @param[in] dev : Structure instance of bma4_dev. * * @note Below macros are used to check the interrupt status. * * Feature Interrupts * - BMA423_STEP_CNTR_INT * - BMA423_ACTIVITY_INT * - BMA423_WRIST_WEAR_INT * - BMA423_WAKEUP_INT * - BMA423_ANY_MOT_INT * - BMA423_NO_MOT_INT * - BMA423_ERROR_INT * * Hardware Interrupts * - BMA4_FIFO_FULL_INT * - BMA4_FIFO_WM_INT * - BMA4_DATA_RDY_INT * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_read_int_status(uint16_t *int_status, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiFeat Sensor Feature * @brief Enables / Disables features of the sensor */ /*! * \ingroup bma423ApiFeat * \page bma423_api_bma423_feature_enable bma423_feature_enable * \code * int8_t bma423_feature_enable(uint8_t feature, uint8_t enable, struct bma4_dev *dev); * \endcode * @details This API enables/disables the features of the sensor. * * @param[in] feature : Variable to specify the features which are to be set in * bma423 sensor. * @param[in] enable : Variable which specifies whether to enable or disable the * features in the bma456 sensor. * *@verbatim * enable | Macros * --------|------------------- * 0x00 | BMA4_DISABLE * 0x01 | BMA4_ENABLE *@endverbatim * * @param[in] dev : Structure instance of bma4_dev. * * @note User should use the below macros to enable or disable the * features of bma423 sensor * * - BMA423_STEP_CNTR * - BMA423_ACTIVITY * - BMA423_WAKEUP * - BMA423_WRIST_WEAR * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_feature_enable(uint8_t feature, uint8_t enable, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiRemap Remap Axes * @brief Set / Get x, y and z axis re-mapping in the sensor */ /*! * \ingroup bma423ApiRemap * \page bma423_api_bma423_set_remap_axes bma423_set_remap_axes * \code * int8_t bma423_set_remap_axes(const struct bma423_axes_remap *remap_data, struct bma4_dev *dev); * \endcode * @details This API performs x, y and z axis remapping in the sensor. * * @param[in] remap_data : Pointer to store axes remapping data. * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_set_remap_axes(const struct bma423_axes_remap *remap_data, struct bma4_dev *dev); /*! * \ingroup bma423ApiRemap * \page bma423_api_bma423_get_remap_axes bma423_get_remap_axes * \code * int8_t bma423_get_remap_axes(struct bma423_axes_remap *remap_data, struct bma4_dev *dev); * \endcode * @details This API reads the x, y and z axis remap data from the sensor. * * @param[out] remap_data : Pointer to store axis remap data which is read * from the bma423 sensor. * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_get_remap_axes(struct bma423_axes_remap *remap_data, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiStepC Step counter * @brief Operations of step counter feature of the sensor */ /*! * \ingroup bma423ApiStepC * \page bma423_api_bma423_step_counter_set_watermark bma423_step_counter_set_watermark * \code * int8_t bma423_step_counter_set_watermark(uint16_t step_counter_wm, struct bma4_dev *dev); * \endcode * @details This API sets the watermark level for step counter interrupt in * the sensor. * * @param[in] step_counter_wm : Variable which specifies watermark level * count * @note Valid values are from 1 to 1023 * @note Value 0 is used for step detector interrupt * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_step_counter_set_watermark(uint16_t step_counter_wm, struct bma4_dev *dev); /*! * \ingroup bma423ApiStepC * \page bma423_api_bma423_step_counter_get_watermark bma423_step_counter_get_watermark * \code * int8_t bma423_step_counter_get_watermark(uint16_t *step_counter_wm, struct bma4_dev *dev); * \endcode * @details This API gets the water mark level set for step counter interrupt * in the sensor * * @param[out] step_counter_wm : Pointer variable which stores the water mark * level read from the sensor. * @note valid values are from 1 to 1023 * @note value 0 is used for step detector interrupt * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_step_counter_get_watermark(uint16_t *step_counter_wm, struct bma4_dev *dev); /*! * \ingroup bma423ApiStepC * \page bma423_api_bma423_reset_step_counter bma423_reset_step_counter * \code * int8_t bma423_reset_step_counter(struct bma4_dev *dev); * \endcode * @details This API resets the counted steps of step counter. * * @param[in] dev : structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_reset_step_counter(struct bma4_dev *dev); /*! * \ingroup bma423ApiStepC * \page bma423_api_bma423_step_counter_output bma423_step_counter_output * \code * int8_t bma423_step_counter_output(uint32_t *step_count, struct bma4_dev *dev); * \endcode * @details This API gets the number of counted steps of the step counter * feature from the sensor. * * @param[out] step_count : Pointer variable which stores counted steps * read from the sensor. * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_step_counter_output(uint32_t *step_count, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiAct Activity Feature * @brief Get output for activity feature of the sensor */ /*! * \ingroup bma423ApiAct * \page bma423_api_bma423_activity_output bma423_activity_output * \code * int8_t bma423_activity_output(uint8_t *activity, struct bma4_dev *dev); * \endcode * @details This API gets the output for activity feature. * * @param[out] activity : Pointer variable which stores activity output read * from the sensor. * *@verbatim * activity | State * --------------|------------------------ * 0x00 | BMA423_USER_STATIONARY * 0x01 | BMA423_USER_WALKING * 0x02 | BMA423_USER_RUNNING * 0x03 | BMA423_STATE_INVALID *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_activity_output(uint8_t *activity, struct bma4_dev *dev); /*! * \ingroup bma423ApiStepC * \page bma423_api_bma423_stepcounter_get_parameter bma423_stepcounter_get_parameter * \code * int8_t bma423_stepcounter_get_parameter(struct bma423_stepcounter_settings *setting, struct bma4_dev *dev); * \endcode * @details This API gets the parameter1 to parameter7 settings of the step * counter feature. * * @param[out] setting : Pointer to structure variable which stores the * parameter1 to parameter7 read from the sensor. * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_stepcounter_get_parameter(struct bma423_stepcounter_settings *setting, struct bma4_dev *dev); /*! * \ingroup bma423ApiStepC * \page bma423_api_bma423_stepcounter_set_parameter bma423_stepcounter_set_parameter * \code * int8_t bma423_stepcounter_set_parameter(const struct bma423_stepcounter_settings *setting, struct bma4_dev *dev); * \endcode * @details This API sets the parameter1 to parameter7 settings of the step * counter feature in the sensor. * * @param[in] setting : Pointer to structure variable which stores the * parameter1 to parameter7 settings read from the sensor. * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_stepcounter_set_parameter(const struct bma423_stepcounter_settings *setting, struct bma4_dev *dev); /** * \ingroup bma421 * \defgroup bma421ApiStepD Step detector * @brief Operations of step detector feature of the sensor */ /*! * \ingroup bma421ApiStepD * \page bma421_api_bma421_step_detector_enable bma421_step_detector_enable * \code * int8_t bma421_step_detector_enable(uint8_t enable, struct bma4_dev *dev); * \endcode * @details This API enables or disables the step detector feature in the * sensor. * * @param[in] enable : Variable used to enable or disable step detector * *@verbatim * enable | Macros * --------|------------------- * 0x00 | BMA4_DISABLE * 0x01 | BMA4_ENABLE *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_step_detector_enable(uint8_t enable, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiAnyMot Any motion Feature * @brief Functions of Any motion feature of the sensor */ /*! * \ingroup bma423ApiAnyMot * \page bma423_api_bma423_set_any_motion_config bma423_set_any_motion_config * \code * int8_t bma423_set_any_motion_config(const struct bma423_anymotion_config *any_motion, struct bma4_dev *dev); * \endcode * @details This API sets the configuration of any-motion feature in the sensor * This API enables/disables the any-motion feature according to the axis set. * * @param[in] any_mot : Pointer to structure variable to configure * any-motion. * * @verbatim * ------------------------------------------------------------------------- * Structure parameters | Description * --------------------------------|---------------------------------------- * | Defines the number of * | consecutive data points for * | which the threshold condition * duration | must be respected, for interrupt * | assertion. It is expressed in * | 50 Hz samples (20 ms). * | Range is 0 to 163sec. * | Default value is 5 = 100ms. * --------------------------------|---------------------------------------- * | Slope threshold value for * | Any-motion detection * threshold | in 5.11g format. * | Range is 0 to 1g. * | Default value is 0xAA = 83mg. * --------------------------------|---------------------------------------- * | Enables the feature on a per-axis * axis_en | basis. * --------------------------------------------------------------------------- * @endverbatim * *@verbatim * Value | axis_en * ---------|------------------------- * 0x00 | BMA423_DIS_ALL_AXIS * 0x01 | BMA423_X_AXIS_EN * 0x02 | BMA423_Y_AXIS_EN * 0x04 | BMA423_Z_AXIS_EN * 0x07 | BMA423_EN_ALL_AXIS *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_set_any_mot_config(const struct bma423_any_no_mot_config *any_mot, struct bma4_dev *dev); /*! * \ingroup bma423ApiAnyMot * \page bma423_api_bma423_get_any_motion_config bma423_get_any_motion_config * \code * int8_t bma423_get_any_motion_config(struct bma423_anymotion_config *any_motion, struct bma4_dev *dev); * \endcode * @details This API gets the configuration of any-motion feature from the * sensor. * * @param[out] any_mot : Pointer to structure variable to configure * any-motion. * * @verbatim * ------------------------------------------------------------------------- * Structure parameters | Description * --------------------------------|---------------------------------------- * | Defines the number of * | consecutive data points for * | which the threshold condition * duration | must be respected, for interrupt * | assertion. It is expressed in * | 50 Hz samples (20 ms). * | Range is 0 to 163sec. * | Default value is 5 = 100ms. * --------------------------------|---------------------------------------- * | Slope threshold value for * | Any-motion detection * threshold | in 5.11g format. * | Range is 0 to 1g. * | Default value is 0xAA = 83mg. * --------------------------------|----------------------------------------- * | Enables the feature on a per-axis * axis_en | basis. * --------------------------------------------------------------------------- * @endverbatim * *@verbatim * Value | axis_en * ---------|------------------------- * 0x00 | BMA423_DIS_ALL_AXIS * 0x01 | BMA423_X_AXIS_EN * 0x02 | BMA423_Y_AXIS_EN * 0x04 | BMA423_Z_AXIS_EN * 0x07 | BMA423_EN_ALL_AXIS *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_get_any_mot_config(struct bma423_any_no_mot_config *any_mot, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiNomot No-Motion Feature * @brief Operations of no-motion feature of the sensor */ /*! * \ingroup bma423ApiNomot * \page bma423_api_bma423_set_no_motion_config bma423_set_no_motion_config * \code * int8_t bma423_set_no_motion_config(const struct bma423_nomotion_config *no_motion, struct bma4_dev *dev); * \endcode * @details This API sets the configuration of no-motion feature in the sensor * This API enables/disables the no-motion feature according to the axis set. * * @param[in] no_mot : Pointer to structure variable to configure * no-motion. * * @verbatim * ------------------------------------------------------------------------- * Structure parameters | Description * --------------------------------|---------------------------------------- * | Defines the number of * | consecutive data points for * | which the threshold condition * duration | must be respected, for interrupt * | assertion. It is expressed in * | 50 Hz samples (20 ms). * | Range is 0 to 163sec. * | Default value is 5 = 100ms. * --------------------------------|---------------------------------------- * | Slope threshold value for * | No-motion detection * threshold | in 5.11g format. * | Range is 0 to 1g. * | Default value is 0xAA = 83mg. * --------------------------------|---------------------------------------- * | Enables the feature on a per-axis * axis_en | basis. * --------------------------------------------------------------------------- * @endverbatim * *@verbatim * Value | axis_en * ---------|------------------------- * 0x00 | BMA423_DIS_ALL_AXIS * 0x01 | BMA423_X_AXIS_EN * 0x02 | BMA423_Y_AXIS_EN * 0x04 | BMA423_Z_AXIS_EN * 0x07 | BMA423_EN_ALL_AXIS *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_set_no_mot_config(const struct bma423_any_no_mot_config *no_mot, struct bma4_dev *dev); /*! * \ingroup bma423ApiNomot * \page bma423_api_bma423_get_no_motion_config bma423_get_no_motion_config * \code * int8_t bma423_get_no_motion_config(struct bma423_nomotion_config *no_motion, struct bma4_dev *dev); * \endcode * @details This API gets the configuration of no-motion feature from the * sensor. * * @param[out] no_mot : Pointer to structure variable to configure * no-motion. * * @verbatim * ------------------------------------------------------------------------- * Structure parameters | Description * --------------------------------|---------------------------------------- * | Defines the number of * | consecutive data points for * | which the threshold condition * duration | must be respected, for interrupt * | assertion. It is expressed in * | 50 Hz samples (20 ms). * | Range is 0 to 163sec. * | Default value is 5 = 100ms. * --------------------------------|---------------------------------------- * | Slope threshold value for * | No-motion detection * threshold | in 5.11g format. * | Range is 0 to 1g. * | Default value is 0xAA = 83mg. * --------------------------------|----------------------------------------- * | Enables the feature on a per-axis * axis_en | basis. * --------------------------------------------------------------------------- * @endverbatim * *@verbatim * Value | axis_en * ---------|------------------------- * 0x00 | BMA423_DIS_ALL_AXIS * 0x01 | BMA423_X_AXIS_EN * 0x02 | BMA423_Y_AXIS_EN * 0x04 | BMA423_Z_AXIS_EN * 0x07 | BMA423_EN_ALL_AXIS *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_get_no_mot_config(struct bma423_any_no_mot_config *no_mot, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiTap Single Tap and Double tap * @brief Single and Double tap feature operations */ /*! * \ingroup bma423ApiTap * \page bma423_api_bma423_single_tap_set_sensitivity bma423_single_tap_set_sensitivity * \code * int8_t bma423_single_tap_set_sensitivity(uint8_t sensitivity, struct bma4_dev *dev); * \endcode * @details This API sets the sensitivity of single tap wake-up feature in the sensor * * @param[in] sensitivity : Variable used to specify the sensitivity of the * Wake up feature. * *@verbatim * Value | Sensitivity * --------|------------------------- * 0x00 | MOST SENSITIVE * 0x07 | LEAST SENSITIVE *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_single_tap_set_sensitivity(uint8_t sensitivity, struct bma4_dev *dev); /*! * \ingroup bma423ApiTap * \page bma423_api_bma423_double_tap_set_sensitivity bma423_double_tap_set_sensitivity * \code * int8_t bma423_double_tap_set_sensitivity(uint8_t sensitivity, struct bma4_dev *dev); * \endcode * @details This API sets the sensitivity of double tap wake-up feature in the sensor * * @param[in] sensitivity : Variable used to specify the sensitivity of the * Wake up feature. * *@verbatim * Value | Sensitivity * --------|------------------------- * 0x00 | MOST SENSITIVE * 0x07 | LEAST SENSITIVE *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_double_tap_set_sensitivity(uint8_t sensitivity, struct bma4_dev *dev); /*! * \ingroup bma423ApiTap * \page bma423_api_bma423_single_tap_get_sensitivity bma423_single_tap_get_sensitivity * \code * int8_t bma423_single_tap_get_sensitivity(uint8_t *sensitivity, struct bma4_dev *dev); * \endcode * @details This API gets the sensitivity of single tap wake up feature in the sensor * * @param[out] sensitivity : Pointer variable which stores the sensitivity * value read from the sensor. * * @verbatim * Value | Sensitivity * --------|------------------------- * 0x00 | MOST SENSITIVE * 0x07 | LEAST SENSITIVE *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_single_tap_get_sensitivity(uint8_t *sensitivity, struct bma4_dev *dev); /*! * \ingroup bma423ApiTap * \page bma423_api_bma423_double_tap_get_sensitivity bma423_double_tap_get_sensitivity * \code * int8_t bma423_double_tap_get_sensitivity(uint8_t *sensitivity, struct bma4_dev *dev); * \endcode * @details This API gets the sensitivity of double tap wake up feature in the sensor * * @param[out] sensitivity : Pointer variable which stores the sensitivity * value read from the sensor. * *@verbatim * Value | Sensitivity * --------|------------------------- * 0x00 | MOST SENSITIVE * 0x07 | LEAST SENSITIVE *@endverbatim * * @param[in] dev : Structure instance of bma4_dev * * @return Result of API execution status * @retval 0 -> Success * @retval < 0 -> Fail */ int8_t bma423_double_tap_get_sensitivity(uint8_t *sensitivity, struct bma4_dev *dev); /** * \ingroup bma423 * \defgroup bma423ApiVersionConfig Version Config * @brief Get version configuration of the sensor */ /*! * \ingroup bma423ApiVersionConfig * \page bma423_api_bma422_huawei_get_version_config bma423_get_version_config * \code * int8_t bma423_get_version_config(uint16_t *config_major, uint16_t *config_minor, struct bma4_dev *dev); * \endcode * @details This API is used to get the config file major and minor information. * * @param[in] dev : Structure instance of bma4_dev. * @param[out] config_major : Pointer to data buffer to store the config major. * @param[out] config_minor : Pointer to data buffer to store the config minor. * * @retval BMA4_OK - Success. * @retval BMA4_E_NULL_PTR - Error: Null pointer error */ int8_t bma423_get_version_config(uint16_t *config_major, uint16_t *config_minor, struct bma4_dev *dev); #ifdef __cplusplus } #endif /*End of CPP guard */ #endif /*End of header guard macro */